Archive

Posts Tagged ‘RF Transmitters & Receivers’

The Greatest Thing to Happen to the Remote Control Since Infared

December 25, 2011 Leave a comment

The NextGen Genius Remote Extender adds RF to your existing remote simply by installingĀ a battery transmitter. Simply install the Remote Extender in place of one of the AA or AAA batteries inside your remote control, then point the receiver or attach the bright eye emitter to the components you wish to control. Control your components from anywhere in the house. Even works through closet doors and closed entertainment system cabinets! Go from room-to-room and control your components up to 100+ feet away, no direct line of sight is needed. Unlike other remote control extenders, you don’t have to attach anything to the front of your remote or be limited to using your remote in one room. The receiver has a built in charger and comes with (2) 2/3 AA specially sized rechargeable batteriess. And by simply installing extra battery transmitters you can convert as many remotes as you like. Works with virtually every remote control!

The NextGen Genius Remote Extender comes in 5 frequencies and colors: Green, Orange, Gray, Yellow and Purple.

Read more

Waterproof PowerCode Wrist-Worn Transmitter for Personal Emergency Signaling

February 14, 2011 Leave a comment

Visonic MCT-211/0-2452-0 Waterproof Wireless Wrist Transmitter

Visonic MCT-211/0-2452-0 Waterproof Wireless Wrist Transmitter

Item# 73988

Price: Normally $79.70
Hot Deal $63.99

MCT-211 is a PowerCode miniature waterproof wrist-worn transmitter, designed for personal emergency signaling and other applications where the transmitter needs to be within easy reach at all times. The transmitter is waterproof and suitable for wearing even in a shower or in other wet environments such as factories, hospitals, gardens, pools and rain conditions. Attractive ergonomic design makes the MCT-211 as convenient to wear on a regular basis as any wristwatch.

When a button is pressed and transmission is initiated, the MCT-transmits a unique, factory programmed, 24-bit digital alarm code. This code is randomly selected from 16 million possible codes and is therefore unique and virtually impossible to accidentally reproduce. MCT-211 uses a coin-type 3-Volt long life lithium battery. To ensure continuous reliable operation, when the battery charge is low, an LED lights during transmission and a low-battery alert is sent to the target receiver. MCT-211 is compatible with PowerMax and all Visonic PowerCode wireless panels and receivers.

  • Easy to wear as a wristband
  • Superior transmission range
  • Attractive, comfortable, ergonomic, waterproof design
  • PowerCode ID factory-selected from 16 million possible combinations
  • 3 Volt coin-type lithium battery
  • Visible and transmitted low battery indications
  • Read more
    *Since we strive to provide you with the lowest prices, prices are subject to change.

    Supervised Hand-held PowerCode Wireless Transmitter

    February 5, 2011 Leave a comment

    Visonic MCT-101/0-2246-2 1 Button Hand-Held Wireless Transmitter

    Visonic MCT-101/0-2246-2 1 Button Hand-Held Wireless Transmitter

    Item# 73985

    Price: Normally $52.42
    Hot Deal $44.49

    MCT-101 (1-button) hand-held PowerCode are hand-held, PowerCode UHF transmitters, especially designed for use in supervised alarm and remote control systems. Transmission is activated by pressing any one of the transmit pushbuttons on the unit. When pressed, each button initiates transmission of a unique 24-bit PowerCode ID which identifies it to the target receiver as if it were a separate transmitter. Each unique ID code is factory-selected from 16 million possible combinations.

    These ergonomically designed hand-held devices have a built-in mode selector which allows the choosing between continuous transmissions for as long as the button is pressed and timed 3-second transmission, no matter how long the button is pressed. Another built-in mode selector is used to enable/disable a once-per-fifteen-minute supervision message or according to local standards. Since messages transmitted by the MCT-101might collide with other messages sent by other PowerCode transmitters, a smart anti-collision transmission sequence is used.

    Operating power is obtained from an internal long-life lithium thionyl chloride battery. An LED lights during transmission, indicating the battery voltage condition. If the LED flashes during transmission, the battery must be replaced immediately. In addition, a transmitter with a weak battery will automatically add a low battery code to each transmission. Compatible receivers are designed to identify this code and activate a corresponding output. Each transmitter of this series is supplied with a belt clip that can be optionally attached to the unit.

    Also available in a 2 or 4 button configuration
    Visonic MCT-102/0-2251-2 2 Button Hand-held Wireless Transmitter
    Visonic MCT-104/0-2256-2 4 Button Hand-held Wireless Transmitter

  • Attractive modern ergonomic design
  • Fully supervised (selectable)
  • Superior transmission range
  • Smart anti-collision algorithm supports multiple simultaneous transmissions
  • PowerCode ID factory-selected from 16 million possible code combinations
  • Long-life standard lithium battery
  • Read more
    *Since we strive to provide you with the lowest prices, prices are subject to change.

    Two-Channel RF Receiver with CODEBUMP Technology

    February 2, 2011 Leave a comment

    SECO-LARM SK-910RB2Q Two-Channel RF Receiver

    SECO-LARM SK-910RB2Q Two-Channel RF Receiver

    Item# 77459B

    Price: Normally $67.70
    Hot Deal $33.99


    Be prepared for today’s thieves with SECO-LARM’s patented CODEBUMP technology. With CODEBUMP, so-called code-grabbers and scanners are rendered obsolete because the RF code changes every time the transmitter button is pressed. In addition, with over 18 quintillion (1.8×1019) codes, the chances of ever repeating a code are virtually non-existent. SECO-LARM’s CODEBUMP transmitters and receivers are perfect for controlling garage and gate openers, car and home alarms, plus much more.

  • Five Programmable output modes:
    4-Second momentary, toggle, latch, validity and 1-second momentary
  • Two Independently programmable channels
  • Compatible with all SECO-LARM transmitters
  • Use to control garage door opener, house lights, alarm control panel, or other devices via remote control
  • Read more
    *Since we strive to provide you with the lowest prices, prices are subject to change.

    Follow

    Get every new post delivered to your Inbox.

    Join 90 other followers

    %d bloggers like this: